What to pay attention to when using a tube ice machine

Update:2022-04-11

Summary:1. The tube ice machine should be installed in a place away from heat sources, without direct sunlight and with good ventilation. The ambient temperat...

1. The tube ice machine should be installed in a place away from heat sources, without direct sunlight and with good ventilation. The ambient temperature should not exceed 35°C to avoid overheating and heat dissipation of the condenser, which will affect the ice-making effect. The ground on which the tube ice machine is installed should be solid and flat, and the tube ice machine must be kept level, otherwise it will cause no deicing and noise during operation.

2. The gap between the back of the ice tube machine and the left and right sides is not less than 30cm, and the top gap is not less than 60cm.

3. The tube ice machine should use an independent power supply, a dedicated line power supply, and be equipped with fuses and leakage protection switches, and must be reliably grounded.

4. The water used by the tube ice machine should meet the national drinking water standards, and a water filter device should be installed to filter impurities in the water, so as not to block the water pipe and pollute the sink and ice mold. And affect the ice making performance.

5. When cleaning the tube ice machine, the power should be turned off. It is strictly forbidden to use water pipes to directly flush the machine, use neutral detergents for scrubbing, and it is strictly forbidden to use acidic, alkaline and other corrosive solvents for cleaning.

6. The head of the water inlet hose must be unscrewed in the ice making machine within two months, and the filter screen of the water inlet valve must be cleaned to prevent the sand and mud impurities in the water from clogging the water inlet, causing the water inlet to become smaller and making ice impossible.

7. The ice making machine must clean the dust on the surface of the condenser every two months. Poor condensation and heat dissipation can cause damage to compressor components. When cleaning, use a vacuum cleaner, a small brush, etc. to clean the oil and dust on the condensing surface. Do not use sharp metal tools to clean it to avoid damaging the condenser.

8. The water pipes, water tanks, storage bins and protective films of the tube ice machine should be cleaned every two months.

9. The tube ice making machine factory should be cleaned when not in use, and the ice mold and the moisture in the box should be dried with a hair dryer, and placed in a non-corrosive gas and ventilated and dry place to avoid storage in the open air.

Hot Products

YT-B-50PN 48L Car Fridge Compressor Portable Refrigerator

Performance parameters: 1. Model:YT-B-50PN Model Number Capacity Cooling Temperature N.W/G.W Unit dimension Package dimension Loading Quantity(20") Loading Quantity(40") Loading Quantity(40"H) YT-B-50PN 48L 10 to -1...

ABD-35L 30L 48W 220V/12V ABS Thermoelectric Cooler

Model No. Capacity Power supply Cooling temperature Heating temperature N.W/G.W Unit dimension (d×w×h) Gift box dimension (d×w×h) Loading quantity(20'') Loading quantity(40''） Loading quantity(40''H) ABD-35L 30.0L AC 10...

ABD-28L 24L 48W AC 100-240V ABS Thermoelectric Cooler

YT-A-32X 25L 50W Red 12V Thermoelectric Cooler Box

Performance parameters: Model：YT-A-32 Model Number Capacity Refrigeration temperature / Heating temperature N.W/G.W Unit dimension Giftbox dimension Package dimension Loading Quantity(20") Loading Quantity(40") Loading Quantit...

YT-E-005C 2.2L 60W AC 110-120V Bullet Ice Maker

Performance parameters: 1. Model：YT-E-005C Model Number Rated Voltage and current Ice making Capacity water tank volume Ice Cube Shape Ice Cube each circle Refrigerant N.W/G.W Unit dimension Package dimension Loading Quanti...

What to pay attention to when using a tube ice machine

Contact Us